However, as backed up by the experience of numerous users, this will still a very good purchase if you don’t need quite that much space.
#Diy standing desk converter pro
We may not have chosen the Prop Plus 36 as one of the best, but that’s mainly because we really liked the spacious design of its bigger brother (the VARIDESK Pro Plus 48) and didn’t want to give awards to very similar products. It does, however, bump your monitor up a little bit.
It’s also nice to see that, when the desk riser is in sitting mode, it doesn’t really lift your workspace much higher than normal – just a tiny 1/2 inch of space is needed to accommodate the keyboard tray. This makes it much easier to keep your arms bent at the ergonomically optimal 90 degrees while standing. This means that you can easily push the keyboard to the back and use the front area for catching up on physical note-taking or drawing up a quick sketch. Not only is the keyboard shelf wide, it’s also deep. Space Enough for More Than Keyboard + Mouse So, bonus points right away for this desk riser. You could, of course, use keyboard controls or an alternative pointing device, but this is likely to reduce productivity for most people (as well as being a totally unnecessary nuisance). The truth is that the ergonomics of a system with a separate keyboard tray and monitor shelf are thrown well out of kilter when you have to reach up or lean forward to access your mouse. “Well, it’s doing its job, isn’t it?”, you might ask. Looking at similar adjustable risers, you will see that many of them have keyboard trays, but these are really only barely enough for that alone. Its wide keyboard tray is actually large enough to hold your mouse and also a cellphone, a file, or a drink. Especially when still getting used to standing desks, most people will want to sit down frequently, so this ease of use is really quite important. All you really have to do is start lowering it and the pneumatic tube will keep it from dropping – there’s no need for you to support it all the way down. It appears, though, that this system was designed to take some of that effort out of your hands and do some of the work itself.
#Diy standing desk converter manual
With some models, manual adjustments involving physically pushing or pulling on the desk require a significant amount of strength. The pneumatic tube helps things move smoothly so that you don’t accidentally lift it or lower it too quickly, possibly throwing your computer monitor to the floor. Users report that it is pretty easy to lift up and lower. Rubber stoppers are found on the bottom of this desk riser to ensure that it doesn’t scratch the surface of your base workspace and to offer even more stability. In fact, it doesn’t even get completely vertical, which helps keep it standing sturdily. Note, though, that this riser doesn’t go past 90 degrees when you move it to an upright position. Risers that only extend vertically don’t have this advantage. This means that, although the swing-out nature of this riser takes up extra space, this is offset by not having to kick your chair out of the way. Secondly, this allows you to leave your chair at your desk while you’re standing. You’ll need to ensure that you actually have a little extra room to the rear before committing to a desk riser like this one.
This has two implications to consider.įirst off, it means that your desk will take up more space, when in use for both sitting and standing, than it would without the riser. Like many risers, this one swings up and out, pushing your standing zone back from where your sitting zone would be. On the other hand, if you don’t make a habit of this and prefer not ruining your original desk by drilling holes through it, you are in luck. So if you’re a leaner – one of those people who just can’t help but put an elbow on every horizontal surface within reach – this may not be the right desk for you.
However, it is worth noting that it could, potentially, get dragged off balance if you were to put undue pressure on its front edge. Actually, you’ll soon see that all of the desk risers we review here are designed to remain balanced even when supporting typical office equipment, and thus don’t need to be physically attached to your base desk.Īt first glance, it looks as though it would topple over in a light breeze, but it appears that physics is on its side and it remains steady. Given the way that this desk works, it’s sort of surprising that it doesn’t need to be bolted to your original desktop.
0 kommentar(er)
